Blog
Cummins ISB, QSB, ISL & QSC Rear Crankshaft Seal Installation Steps
Precision rear main crankshaft oil seal installation and PTFE lip protection guidelines for commercial Cummins mechanics.
Installing a new rear main crankshaft seal (#5405392) after pulling the transmission and flywheel on a Cummins ISB 5.9/6.7, QSB, ISL, QSC, or C8.3G engine? Follow this step-by-step professional workshop procedure to clean and dry the crankshaft flange and housing bore, mount the M20198 (5395259) pilot and driver assembly, and press the seal to exact factory depth.

Why Hammers & Oil Lubrication Ruin Modern Cummins Rear Main Seals
On Cummins ISB, QSB, ISL, QSC, and C8.3G engines, rear crankshaft seal #5405392 is an engineered PTFE/unitized seal assembly designed to transfer a microscopic PTFE film onto a clean, dry crankshaft flange during initial rotation. Technicians who coat the crankshaft flange or PTFE lip in engine oil or grease—or who tap the seal into the rear cover using a hammer and drift—cause immediate seal failure: oil prevents proper PTFE transfer (resulting in chronic weeping), while hammer impacts cock the carrier and fold the PTFE lip backward. Utilizing the 3.00-pound M20198 Rear Crankshaft Seal Installer (Direct Cummins 5395259 Replacement) eliminates installation errors by anchoring squarely to the crankshaft rear flange and pressing the seal straight into the bore to calibrated depth.
The 5-Step Cummins ISB / QSB / ISL / QSC Rear Seal Installation Protocol
- Remove Flywheel, Housing Cover (If Required) & Old Rear Seal: Support and remove the transmission, clutch/flexplate, and flywheel, then extract the worn rear crankshaft seal without scratching the crankshaft flange OD or rear housing bore.
- Clean & Completely Dry Crankshaft Flange and Housing Bore: Wipe the crankshaft rear sealing journal and rear housing bore spotless with brake/parts cleaner and a lint-free cloth—confirming zero oil, grease, or old sealant remains on either surface.
- Mount M20198 Pilot Plate & Position Dry Seal #5405392: Bolt the M20198 inner pilot guide squarely to the rear crankshaft flywheel bolt holes, then slide the new, completely dry Cummins rear seal (#5405392) squarely onto the pilot sleeve without touching or distorting the PTFE lip.
- Slide M20198 Driver Cup Over Pilot & Press Seal Smoothly: Place the M20198 outer driver cup over the central guide stud, thread on the forcing nut, and tighten smoothly by hand with a wrench until the driver bottoms squarely against the pilot/crankshaft depth stop.
- Remove M20198 Installer, Inspect Seating & Allow Dry Set Time: Unbolt and remove the M20198 toolset, visually confirm uniform 360-degree seal depth in the housing, reinstall the flywheel and transmission, and allow the dry PTFE lip to settle per Cummins service guidelines before starting the engine.
PRO-TECH DRY PTFE INSTALLATION & HAND-PRESS MANDATE:
DO NOT LUBRICATE CUMMINS PTFE REAR SEAL #5405392 OR THE CRANKSHAFT FLANGE WITH OIL OR GREASE! Install completely clean and dry so the PTFE lip seats properly! NEVER USE AN IMPACT WRENCH ON THE M20198 INSTALLER—advance the forcing nut smoothly by hand until the driver bottoms on its depth stop!
3.00 lbs Precision Cummins ISB/QSB/ISL/QSC/C8.3G Rear Crankshaft Seal Installer (5395259). Seat Seal #5405392 True.
Get the M20198 Seal Installer Now
overall rating:
my rating:
log in to rate