Jump to the main content

Secure Checkout

Blog


Detroit DD13, DD15 & DD16 Rear Crankshaft Seal Replacement Steps

Precision drivetrain service and dry PTFE rear crankshaft seal installation guidelines for commercial diesel mechanics.

Step-by-step close up layout of W470589004300 press driver seating a new rear crankshaft seal on a Detroit DD15 engine

Replacing a leaking rear crankshaft main oil seal on a Detroit Diesel DD13, DD15, or DD16 engine during a clutch job, transmission overhaul, or in-frame rebuild? Follow this step-by-step professional workshop procedure to set up the W470589004300 extraction bridge, pull the old seal cleanly, clean and dry the crankshaft journal, mount the new PTFE seal dry, and draw the driver down flush to exact factory depth.

Why Prying & Lubricating PTFE Seals Ruin Detroit DD13/DD15/DD16 Rear Mains

On Detroit Diesel DD13, DD15, and DD16 engines, the rear main crankshaft seal utilizes a high-tech PTFE (Teflon) sealing lip designed to transfer a microscopic lubricating film onto the dry crankshaft journal during initial engine startup. Technicians who pry out the old seal with screwdrivers risk scratching the polished crankshaft flange—creating an instant leak channel. Equally critical, mechanics accustomed to old-school rubber lip seals who apply engine oil or grease to a new Detroit PTFE seal destroy its PTFE transfer memory, causing massive crankcase oil leaks within hours of operation. Furthermore, tapping the seal in with a hammer bends its outer shell and prevents proper lip crush. Utilizing the 10.00-pound W470589004300 Rear Crankshaft Seal Remover & Installer eliminates all installation hazards by pulling old seals axially and pressing new dry PTFE seals straight down until the driver bottoms against its built-in OEM depth stop.

The 5-Step Detroit DD13, DD15 & DD16 Rear Main Seal Service Protocol

  1. Remove Flywheel & Mount W470589004300 Extraction Bridge: Remove the transmission, clutch, and flywheel. Bolt the W470589004300 extraction fixture squarely onto the crankshaft rear flange and engage the puller screws into the old rear seal casing.
  2. Extract Old Rear Main Seal Axially: Turn the central forcing screw clockwise with a hand wrench to draw the old rear main seal straight out of the flywheel housing bore without touching crankshaft sealing lands.
  3. Clean & Dry Crankshaft Flange and Housing Bore: Thoroughly clean the crankshaft sealing journal and flywheel housing counterbore using brake/parts cleaner and lint-free cloths. Ensure both surfaces are 100% clean, oil-free, and completely dry.
  4. Position Fresh PTFE Seal Dry on Guide Pilot: Mount the new Detroit OEM PTFE rear crankshaft seal (e.g., A4729970046 or A0159974946) completely dry onto the W470589004300 installer guide pilot—do NOT apply any oil or grease to the seal lip or crank flange.
  5. Advance Forcing Nut to Seat Seal to OEM Depth: Position the press driver disc over the guide studs, thread on the central forcing nut, and turn clockwise until the driver bottoms firmly against its built-in depth stop shoulder, setting exact factory seal depth and concentricity.

PRO-TECH DRY PTFE INSTALLATION & DEPTH STOP MANDATE:

NEVER APPLY OIL OR GREASE TO DETROIT PTFE REAR MAIN SEAL LIPS OR CRANKSHAFT JOURNALS! Installing PTFE seals lubricated WILL ruin their self-lubricating transfer memory and cause immediate oil leaks! ALWAYS advance the W470589004300 driver until it contacts the depth stop shoulder!

10.00 lbs Precision Guided Detroit DD13/DD15/DD16 Rear Main Seal Remover & Installer Kit. Protect Crankshafts.

Get the W470589004300 Kit Now

overall rating:
my rating: log in to rate

Back to Blog Home