Jump to the main content

Secure Checkout

Blog


Why the ATC37720 Roller Lifter & Tappet Holding Kit is Mandatory for Mack E6, E7 & E9 Camshaft Service

Prevent dropped roller lifters, scored camshaft journals, and unnecessary head removals on Mack E6, E7 & E9 engines.

ATC37720 For Mack E6 E7 E9 Roller Lifter Tappet Holding Kit J-37720C Main View

Removing or replacing a camshaft, servicing rocker arms, or performing an in-frame top-end overhaul on Mack Trucks E6, E7, and E9 heavy-duty commercial diesel engines? Attempting to suspend heavy roller lifters and tappets out of the way of camshaft journals using telescopic pencil magnets, O-ring picks, shop rags, or improvised wire hooks—or pulling cylinder heads unnecessarily just to extract lifters—causes catastrophic crankcase damage and massive unbilled labor hours. On Mack E6, E7, and E9 engines, heavy precision roller lifters ride directly on camshaft lobes deep inside block lifter bores. If a lifter slips off a weak magnet while sliding the camshaft out or in, the hardened steel roller assembly drops straight down into the oil pan or jams against cam lobes—chipping precision roller bearings, scoring machined cam journals, or forcing complete oil pan removal to retrieve dropped parts. Worse, mixing up worn roller lifters between cylinder bores destroys matched cam-to-roller wear patterns, leading to rapid camshaft lobe spalling. Engineered for professional commercial diesel technicians, Mack dealership service stalls, fleet maintenance facilities, and heavy engine rebuilders as a direct high-strength replacement for OEM tool part numbers J-37720C and J-37720-C, the ATC37720 For Mack E6 E7 E9 Roller Lifter Tappet Holding Kit provides a 7.00-pound precision-machined two-piece threaded rod and retention grommet set—engineered specifically to clear tight Mack RD cab firewalls while holding all roller lifters securely above camshaft lobes in exact cylinder order.

ATC37720 For Mack E6 E7 E9 Roller Lifter Tappet Holding Kit J-37720C Main View

The Critical Physics of Two-Piece Firewall Clearance & Positive Grommet Retention

On Mack E6, E7, and E9 engines installed inside tight-clearance conventional and vocational chassis such as Mack RD cabs, rear cylinder pushrod openings sit directly beneath overhanging firewall and cowl structures. Full-length one-piece lifter tools cannot be inserted into rear cylinders without unbolting engine mounts or pulling the cab. The ATC37720 (ATC 37720C) solves this exact geometry constraint using precision-machined two-piece rods that screw together seamlessly once positioned over the pushrod openings. Each rod lowers directly down the pushrod bore to engage the roller lifter/tappet positively. Once lifted slightly above the camshaft lobe clearance plane, sliding the heavy-duty retention grommet down the shaft against the cylinder head deck locks each lifter in place—preserving exact cylinder-by-cylinder orientation and preventing accidental drops during camshaft extraction and installation.

  • Targeted Mack E6, E7 & E9 Platform Fitment – Purpose-built specifically for roller lifter and tappet retention on Mack Trucks E6, E7, and E9 commercial diesel engines.
  • Direct Mack / Kent-Moore OEM Tool Interchange – Direct high-strength replacement for factory tool part numbers **J-37720C** and **J-37720-C** (ATC37720 / ATC 37720C).
  • Two-Piece Threaded Rods for Tight Mack RD Cabs – Manufactured in two screw-together sections to clear overhanging firewalls on rear cylinders without pulling heads or cabs.
  • Positive Grommet Retention & Bore Organization – Sliding retention grommets lock lifters cleanly above camshaft lobes while keeping every roller lifter matched to its original cylinder bore.
  • Substantial 7.00 lbs Heavy-Duty Shop Steel Build – Precision-machined structural alloy tool steel engineered for continuous daily use in commercial fleet and rebuild stalls.

Stop Dropping Lifters into Crankcases. Command Total Mack E6/E7/E9 Camshaft Service Precision.

The ATC37720 For Mack E6 E7 E9 Roller Lifter Tappet Holding Kit J-37720C is an essential capital asset for commercial truck repair centers, Mack dealership service stalls, fleet maintenance facilities, and heavy engine rebuilders. Prevent dropped roller lifters, eliminate unnecessary cylinder head removals, and service Mack E6, E7, and E9 camshafts with complete mechanical authority using Apex tools.

7.00 lbs Master Mack E6 / E7 / E9 Two-Piece Roller Lifter & Tappet Holding Kit. Protect Camshafts & Lifters.

Order the ATC37720 Holding Kit – $580.00

Technical Specifications

Technical Metric Value / Fitment Reference Guidelines
Target Engine Platforms Mack Trucks E6, E7, and E9 Heavy-Duty Commercial Diesel Engines
Primary Operational Functions Positive retention and elevation of roller lifters/tappets during camshaft removal and top-end service
Specialty Tool Cross Reference Direct OEM replacement for J-37720C and J-37720-C (ATC37720 / ATC 37720C)
Rod Architecture & Chassis Fitment Two-piece screw-together rods designed specifically to clear tight Mack RD cab firewalls
Kit Contents Architecture Two-piece threaded lifter holding rods and sliding shaft retention grommets
Part / Model Reference Number ATC37720 (ATC 37720 / ATC 37720C / J-37720C / J-37720-C)
Construction Metallurgy High-tensile precision-machined structural alloy tool steel with heavy-duty elastomer grommets
Total Package Shipping Weight 7.00 lbs (Professional Mack engine overhaul and camshaft service kit)

overall rating:
my rating: log in to rate

Back to Blog Home