Jump to the main content

Secure Checkout

Blog


Mack E6, E7 & E9 Roller Lifter Holding & Camshaft Removal Steps

Precision valve train maintenance and roller lifter retention guidelines for commercial Mack mechanics and fleet technicians.

Step-by-step close up layout of ATC37720 holding rods and grommets retaining roller lifters on a Mack E7 engine

Removing or replacing a camshaft on a Mack E6, E7, or E9 diesel engine without pulling the cylinder heads? Follow this step-by-step professional workshop procedure to assemble the two-piece ATC37720 holding rods inside tight Mack RD cab clearances, engage roller lifters through pushrod openings, lock the retention grommets, and slide the camshaft out safely.

Why Magnets & Improvised Wire Hooks Fail on Mack E6, E7 & E9 Lifters

On Mack E6, E7, and E9 commercial diesel engines, heavy-duty roller lifters and tappets sit inside deep block bores directly above the camshaft. Technicians who attempt to hold lifters up with pencil magnets or bent wires during an in-frame camshaft swap risk catastrophic failure: heavy oil film breaks magnetic grip easily, dropping hardened roller assemblies onto spinning or sliding camshaft journals—chipping roller edges or dumping lifters into the oil pan. Furthermore, Mack RD vocational cabs leave minimal overhead clearance above rear pushrod bores, making long single-piece tools unusable. Utilizing the 7.00-pound ATC37720 Roller Lifter Tappet Holding Kit (J-37720C Equivalent) completely eliminates both hazards. Its two-piece screw-together rods clear tight firewalls effortlessly, while sliding shaft grommets hold every lifter mechanically suspended above the camshaft lobes in exact bore order.

The 5-Step Mack E6, E7 & E9 Roller Lifter Retention Protocol

  1. Remove Valve Covers, Rocker Assemblies & Pushrods: Remove valve covers, unbolt and remove rocker arm shafts/assemblies, and withdraw all pushrods—labeling pushrods in order for reinstallation.
  2. Assemble Two-Piece ATC37720 Rods for Cab Clearance: In tight-fit Mack RD cabs, insert the lower rod section into the rear pushrod opening first, then screw the upper rod section tightly together with the lower section (on open-access cylinders, screw the two-piece rods together prior to insertion).
  3. Lower Rods Through Pushrod Openings to Engage Lifters: Lower each assembled ATC37720 holding rod straight down through the pushrod opening until positive contact is made with the roller lifter/tappet below.
  4. Lift Lifters Above Cam Lobes & Lock Retention Grommets: Slowly lift the holding rod upward slightly until the roller lifter/tappet clears the camshaft lobe peak, then slide the included retention grommet firmly down the rod shaft to hold the lifter securely in the elevated position.
  5. Repeat Across All Cylinders & Extract Camshaft: Repeat the elevation and grommet-locking step on every cylinder across the engine, verify all lifters are suspended clear of the cam tunnel, and withdraw the camshaft smoothly out of the front of the block.

PRO-TECH ROD THREAD TIGHTNESS & OVER-LIFTING MANDATE:

ALWAYS SCREW THE TWO-PIECE ATC37720 ROD SECTIONS TIGHTLY TOGETHER BEFORE LIFTING LIFTERS! Loose rod joints can unthread inside the block! DO NOT OVER-LIFT LIFTERS OUT OF THEIR UPPER BORE GUIDES—lift only high enough to clear camshaft lobes and slide the grommet down firmly! Always refer to your Mack service manual for latest instructions.

7.00 lbs Master Mack E6 / E7 / E9 Two-Piece Roller Lifter & Tappet Holding Kit. Protect Camshafts & Lifters.

Get the ATC37720 Holding Kit Now

overall rating:
my rating: log in to rate

Back to Blog Home